ASTM G154-06 PDF

Engaged Expert Terry Candlish discusses ASTM G and G tests which are used to evaluate sunlight and moisture exposure. ASTM. ASTM G & G UV Testing. The UV testing was performed on ecomère by Touchstone Labs in Tridelphia, WV, again at the request of Southern . ASTM G – Designation: G – 06 Standard Practice for Operating Fluorescent Light Appara.

Author: Mikagal Nirg
Country: Gabon
Language: English (Spanish)
Genre: Relationship
Published (Last): 20 October 2012
Pages: 143
PDF File Size: 9.72 Mb
ePub File Size: 2.80 Mb
ISBN: 693-2-27046-194-2
Downloads: 25880
Price: Free* [*Free Regsitration Required]
Uploader: Voodoonris

Note—A footnote was added to Table X2. These exposures may include a means to introduce moisture to the test specimen. ASTM International recommends that a comparable material of identified performance a control be exposed at the same time as the test specimen.

Current edition approved June 5, This standard does not purport to address all of the safety concerns, if any, associated with adtm use.

Hemispherical on 37 Tilted Surface. The ASTM G and G tests empower manufacturers to design products that can withstand exposure to sunlight g154-60 moisture.

From environmental and dynamic testing to highly specialized tests such as bird strike and hydrodynamic ditching testing, we’re the trusted testing partner to the world’s most recognized component and system manufacturers.

Hemispherical on asttm degree Tilted Surface.

ASTM G154 and G155 Explained

This is because the UVA has a special power distribution in the short wave UV region that is similar to sunlight sstm has already been? The pH of the water used should be reported. Cracking, peeling, de-glossing, oxidation, and tensile weakening are additional outcomes of exposure; sometimes such deterioration can even occur through window glass.

TOP Related Posts  CARLOS MONSIVAIS AMOR PERDIDO PDF

Care should be taken to keep silica levels below 0.

ASTM G and G Explained | Element

In xenon arc testing, different optical filters may be applied to shift testing conditions for daylight, window glass, or extended UV spectrum exposure. These lamps emit different amounts of total g145-06, but both peak at nm and produce the same UV wavelengths in the same relative proportions.

The spectral power distribution data is g1544-06 lamps within the aging recommendations of the device manufacturer. The lowest wavelength measured shall be no greater than nm.

This data is provided for comparison purposes only. As shown in Fig. It is recommended that at least three replicates of each material evaluated be exposed in each test to allow for statistical evaluation of results. Due to time constraints, however, many producers employ the G and G laboratory chamber tests for reliable exposure results in shorter time periods. E Previous versions of this standard used window glass? The lamps shown in this section are representative of their type.

Because xenon asym light is most similar to natural sunlight, we generally use the ASTM G test for outdoor weatherization testing. For instance, a slight shift in formula may produce twice as much resistance to weathering.

TOP Related Posts  KSIA WOBEC BEZPIEKI PDF

The control specimens shall be exposed simultaneously with the test specimen s in the same device. Different types of fluorescent UV lamp sources are described. Your comments are invited either asm revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. NOTE 9—Typically, these devices control by black panel temperature only.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Precision and Bias Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Cycle 6 has been used for high irradiance exposures of coatings and plastics. It may be tempting to assume that shorter wavelengths, continuous exposure, high temperatures, and other variables can result in more intense acceleration. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Following are some representative exposure conditions. When rays of sunlight—particularly UV rays—bombard a surface, they degrade smaller pigment particles, changing the surface color and creating a chalky effect.