The 3G3MV is a miniature frequency inverter incorperating an open loop vector control Furthermore, the 3G3MV suppresses the revolution fluctuation caused. OMRON products are manufactured for use according to proper procedures by a qualified .. 3G3MV-P10CDT Operation Manual (this manual) and the CPM1/. A maximum of four errors can be displayed. U Software No. OMRON use only. U Output power. W. Monitors the output power of the Inverter (see note.
|Published (Last):||18 June 2015|
|PDF File Size:||7.8 Mb|
|ePub File Size:||19.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
Not just a picture from the manufacturer’s website, but the actual piece of equipment you would receive. These features are outlined below and explained in detail in Chapter 6.
Sysdrive 3g3mv-a Sysdrive 3g3mv-a Sysdrive 3g3mv-a Sysdrive 3g3mv-a Sysdrive 3g3mv-a Sysdrive 3g3mv-a Select the ideal method according to the application. It’s like having the store come to you! Page Chapter 11 Using the Inverter for a Motor ON Multi-function input 2 1: Not doing so may result in electrical shock.
For example, no settings for multi-step speed reference 3 or 4 will be required if only frequency references 1 through 4 are used. Page Communications Chapter 7 Step Step number.
Omron SYSDRIVE 3G3MV User Manual
ojron Page 7 Caution Install external breakers and take other safety measures against short-circuiting in external wiring. Length l Set the length of the data.
A parameter setting makes it possible to output pulse monitor signals from these terminals. Down command Acceleration Deceleration Advanced Operation Chapter 6 Energy-saving Ojron The energy-saving control function automatically saves unnecessary power that 3g3mf uselessly consumed while the load is light. Local or remote selection is possible only when the Inverter is not in operation.
Doing so may result in injury or damage to the product. The following description provides information on these modes and how to select them. Warning Labels Warning labels are pasted on the product as shown in the following illustration. Terminal Block Design Chapter 2 Terminal Block To wire the terminal block of the Inverter, remove the front cover, terminal cover unless the Inverter is a V modeland bottom cover from the Inverter. Use it when switching the motor from a commercial power supply op- eration to Inverter operation, when starting with the Inverter a motor turned by external force, and so on.
3G3MV A Omron | Controller,motor,speed,kW,3 phase,Vac | | RS Components
Select peripheral devices which meet the specifications and wire correctly. Take the following actions to prevent noise. ON Multi-function input terminal 2 S2 1: Function Frequency reference loss 1 to 15 Not used. Chapter 5 Basic Operation To change the frequency of frequency reference 2, for example, turn ON only the multi- function input terminal where multi-step speed reference 2 is set, and turn OFF any other multi-function input terminal.
Please, use the noise filters as explained in Chapter The Inverter in energy-saving control estimates the capacity of the load from the motor current and controls the output voltage of the Inverter when the load is light so that only the power required is provided to the motor.
This braking is used for stopping and starting the motor rotating by inertia with no regenerative processing. Page 4 Maximum Applicable Motor Capacity 0. Increase the derivative D time in n within a range causing no vibration. The functions in parentheses are the default settings. Select the CRC check code and set the initial value to Page 88 Preparing for Operation and Monitoring Chapter 3 Display Name Probable cause Remedy Copy error An attempt was made to Check that the Inverters are copy or verify the parameter the same in voltage and set values while the control mode.
Born to drive machines; v class three-phase input 0. D Wires Used Use shielded, twisted-pair wires for wiring in order to prevent the Inverter from malfunc- tioning due to noise.
Omron 3G3MV-AB (3G3MVAB) – Axdos AB | PLCSWEDEN | Automation Spare Parts
The output current of the Inverter is comparatively high. Don’t show me this message again. Please enter a message. Chapter 5 Basic Operation Setting Frequency References by Pulse Train Input By setting n for frequency reference selection to 5 for enabling the pulse train reference control terminal, frequency references can be executed by pulse train input through the PR terminal.
Be sure to set the periods according to the application.
Page Communications Chapter 7 Register No. Page Chapter 5 Basic Operation To change the frequency 3g3nv frequency reference 2, for example, turn ON only the multi- function input terminal where multi-step speed reference 2 is set, and turn OFF any other multi-function input terminal.
Click on New Protocol with the left button of the mouse. Increase the integral I time in n within a range causing no vibration.